Here in the next paragraph yow will discover a good deal of excellent expertise pertaining to How to Install a Bathtub.
Installing a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably tough project. If the old tub is conveniently available, the task can move easily; if you have to open up a wall to get rid of the old tub as well as position the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub and also embeded in the new one. Make certain you have qualified on your own for the job as well as fit attempting it. As opposed to working with a contractor to take over a halfway-completed task, it is better to think about using one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will certainly aid you install a new bath tub in your restroom if you have actually currently bought a new bathtub as well as don't require to transform the arrangement of your previous supply of water pipelines.
Your tools as well as product list must make up the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be rather troublesome because of the limited gain access to that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. When the supply pipes have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this process. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin making sure that the washers are in place between the faucet and also the sink. Protect the tap in place with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former type should be attached to the tap ends first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of both wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the level checks out degree.
To set up faucets, fit the bottom of the furthest versatile faucet adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Turn on the water supply and also check all joints and also new pipework for leakages and also tighten them if needed. Fill the tub and likewise check the overflow electrical outlet and the regular outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the bath tub should wait until the tub has actually been used a minimum of when as this will certainly settle it into its last placement.
Preparing for the Installation
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of both taps making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to fracture an inflexible seal, creating the water to pass through the wall between the bathroom as well as the tiling, causing complications with dampness and also feasible leaks to the ceiling below.
You can choose from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealant can crack rather early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily readily available on the market. It is advisable to fit the ceramic tiles using waterproof or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub? Put feedback down below. We'd be pleased to listen to your suggestions about this piece. We are looking forward that you come back again soon. Feel free to set aside a second to share this entry if you enjoyed it. I am grateful for your time. Don't hesitate to check up our blog back soon.
Schedule Service Now